MCA 101 Profibus
 |
By operating the FC 300 frequency converter via a field bus you
can reduce the capital cost of your system, communicate faster and
more efficiently, and enjoy a simpler interface
- PROFIBUS DP V1 gives you wide compatibility, a high level of
availability, supported by all major PLC vendors.
Compatible with future versions
- Fast and efficient communication, transparent installation,
advanced diagnosis and paremeterisation and auto configuration
of process data via GSD-file
- A-cyclic parameterisation using PROFIBUS DP V1, PROFIdrive
or Danfoss FC profile state machines, PROFIBUS DP V1, Master
Class 1 and 2
|
MCA 104 DeviceNet
 |
DeviceNet offers robust, efficient data handling because it is
based on Producer / Consumer technology
- This modern communications model offers key capabilities
that allow the user to effectively determine what information is
needed and when
- Users also benefit from ODVA's strong conformance tseting
policies, that ensure products are interoperable
|
MCB 101 General Purpose I/O Option
 |
I/O option offers an extended number of control inputs and
outputs
- 3 digital inputs 0 - 24 V : Logic '0' < 5 V; Logic '1' > 10V
- 2 analogue inputs 0 - 10 V : Resolution 10 bit plus sign
- 2 digital outputs NPN / PNP push pull
- 1 analogue output 0 / 4 - 20 mA
- Spring loaded connection
- Separate parameter settings
|
MCB 102 Encoder Option
 |
A universal option for connection of encode feedback from either
a motor or a process. Feedback for asynhronous or brushless
servo (Permanent magnet) motors.
- Encode module supports Incremental encoders and SinCos
encoders as Hyperface
- Power supply for encoders
- RS422 interface
- Plug and play principle
- Fit to all FC300 AutomationDrives
- Connection to all standard 5V incremental encoders
- Spring loaded connection
|
MCB 103 Resolver Option
 |
Supports resolver feedback from brushless servo motors and
feedback for flux vector controlled asynchronous motors in rough
environments
- Primary voltage : 4-8 Vrms
- Primary Frequency : 2.5kHz - 15kHz
- Primary current max : 50 mA rms
- Secondary input voltage : 4 Vrms
- Resolution : 10 bit @ 4 Vrms input amplitude
- Spring loaded connection
- Separate parameter settings
|
MCB 105 Relay Options
 |
Gives the possibility to extend the relay functions with 3 extra
relay outputs. The relay option fits into slot B in FC 301 or
FC 302 AutomationDrive. Max Terminal Load:
- AC-1 Resistive load 240V AC - 2A
- AC-15 Inductive load @ cos Ф 0.4 -
0.2 A
- DC-1 Resistive load 240V AC - 1 A
- DC-13 Inductive Load @ cos Ф
0.4 - 0.1 A
Min. Terminal Load
- DC 5 V - 10 mA
- Max switch rate at rated load / min. load - 6 min-1
/ 20 sec-1
- Plug and play principle and fits in to
slot B
- Protected control cable connection
- Spring loaded connection of control wires
- Selection of relay functions in normal
parameter settings
|
MCB 108 Safe PLC Interface
 |
The FC 302 provides a safety input based on a single pole 24 V
DC input. For the majority of applications this input enables the
user to implement afety in a cost effective way. For
applications that work with mroe advanced products like Safety PLC,
Lightcurtains etc, the new Safe PLC interface engables the
connection of a two wire safety link.
The Safe PLC interface allows the Safe PLC to interrupt on the
plus or the minus link without interfering the sensor signal of the
Safe PLC. |
MCO 305 Progammable Motion Controller
|
An integrated programmable Motion Controller for FC 301 and FC
302; it adds functionality and flexibility to the already very
comprehensive standard functionality of these drives. MCO 305
is optimised for all types of positioning and synchronising
applications. Basic Features include:
- Synchronisation (electronic shaft), Positioning and
electronic Cam control
- 2 inputs supporting both incremental and absolute encoders
- 2 imputs supporting both incremental and absolute encoders
- 1 encoder output (virtual master function)
- 10 digital inputs 8 digital outputs
- Sending and receiving data via Filedbus interface (requires
Fieldbus option)
- PC software tools for programming and commissioning
|
MCB 107 24VDC Supply Option
 |
This option is used for connection to an external DC supply to
keep the control section and any option installed active by mains
power down. Slot D.
- Input voltage range - 24 V DC +/- 15% (max. 37 V in 10 sec)
- Max. input current - 2.2A
- Max. cable length - 75 m
- Input capitance load - < 10 uF
- Power-up delay - < 0.6 s
- Simple to install in drives on existing machines
- Keep the control board and options active by power cut
- Keep fieldbuses active by power cuts
- Available pre-installed in FC300 AutomationDrive from
factory
|
LCP 102 Graphical Local Control Panel
|
- Multi language display
- FC 300 status messages
- Quick menu for simple commissioning
- Parameter setting and explanation of parameter function
- Adjusting of parameters
- Full parameter backup and copy function
- Alarm logging
- Info bottom : explains the function of the selected item on
display
- Hand operated start-stop or selection of Automatic mode
- Reset function
- Displaying trend graph
|
LCP 101 Numerical Local Control Panel
|
The numeric control panel offers an excellent MMI interface to
FC 300 Automation. The LCPs supports both drive types FC 301
and FC 302.
- FC 300 status messages
- Quick menu for easy commissioning
- Parameter
- Parameter setting and adjusting
- Hand operated start-stop function or selection of Automatic
mode
- Reset function
|
LCP Panel Mounting Kit
|
- IP65 Enclosure Front
- 3 m cable for connection of LCP and FC300
- Gasket for sealing
- Finger screws for easy fitting
- Supports LCP101 and LCP102
|
 |
Profibus adaptor Sub D9 Connector
The adaptor makes linking of field bus connections pluggable. |
 |
Decoupling plate for fieldbus cables
Makes fieldbus mounting robus |
 |
IP21 / Type 12 (NEMA1) kit
The IP21 / Type 12 (NEMA1) kit is used for installation of FC 300
drives in dry environments. The enclosure kits are available
for frame sizes A2 and A3.
- Supports FC 300 Automation drives power sizes 0.25 to
7.5kW
- Used on standard FC 300 AutomationDrives without and with
mounted option modules
- IP41 on top side
- PG 16 and PG21 holes for glands
|
 |
Removable Fan
The fan can easily be removed and remounted for easy cleaning |
Power options available
- Brake resistors
- LC filters
- dU / dt filter
- Harmonic filters (AHF)
Errors and omissions exempted. |
Click for printer friendly version